rf24-pio/RF24.h

/*
 Copyright (C) 2011 James Coliz, Jr. <maniacbug@ymail.com>

 This program is free software; you can redistribute it and/or
 modify it under the terms of the GNU General Public License
 version 2 as published by the Free Software Foundation.
 */

#ifndef __RF24_H__
#define __RF24_H__

#include <inttypes.h>

typedef enum { RF24_1MBPS = 0, RF24_2MBPS } rf24_datarate_e;
typedef enum { RF24_CRC_8 = 0, RF24_CRC_16 } rf24_crclength_e;

/**
 * Driver for nRF24L01(+) 2.4GHz Wireless Transceiver
 */

class RF24
{
private:
    uint8_t ce_pin; /**< "Chip Enable" pin, activates the RX or TX role */
    uint8_t csn_pin; /**< SPI Chip select */
    uint8_t payload_size; /**< Fixed size of payloads */
    boolean ack_payload_available; /**< Whether there is an ack payload waiting */
    uint8_t ack_payload_length; /**< Dynamic size of pending ack payload. Note: not used. */
    uint64_t pipe0_reading_address; /**< Last address set on pipe 0 for reading. */

protected:
    /**
     * @name Low-level internal interface.
     *
     *  Protected methods that address the chip directly.  Regular users cannot
     *  ever call these.  They are documented for completeness and for developers who
     *  may want to extend this class.
     */
    /**@{*/

    /**
     * Set chip select pin
     *
     * @param mode HIGH to take this unit off the SPI bus, LOW to put it on
     */
    void csn(int mode) ;

    /**
     * Set chip enable
     *
     * @param mode HIGH to actively begin transmission or LOW to put in standby.  Please see data sheet
     * for a much more detailed description of this pin.
     */
    void ce(int mode);

    /**
     * Read a chunk of data in from a register
     *
     * @param reg Which register. Use constants from nRF24L01.h
     * @param buf Where to put the data
     * @param len How many bytes of data to transfer
     * @return Current value of status register
     */
    uint8_t read_register(uint8_t reg, uint8_t* buf, uint8_t len) ;

    /**
     * Read single byte from a register
     *
     * @param reg Which register. Use constants from nRF24L01.h
     * @return Current value of register @p reg
     */
    uint8_t read_register(uint8_t reg);

    /**
     * Write a chunk of data to a register
     *
     * @param reg Which register. Use constants from nRF24L01.h
     * @param buf Where to get the data
     * @param len How many bytes of data to transfer
     * @return Current value of status register
     */
    uint8_t write_register(uint8_t reg, const uint8_t* buf, uint8_t len);

    /**
     * Write a single byte to a register
     *
     * @param reg Which register. Use constants from nRF24L01.h
     * @param value The new value to write
     * @return Current value of status register
     */
    uint8_t write_register(uint8_t reg, uint8_t value);

    /**
     * Write the transmit payload
     *
     * The size of data written is the fixed payload size, see getPayloadSize()
     *
     * @param buf Where to get the data
     * @param len Number of bytes to be sent
     * @return Current value of status register
     */
    uint8_t write_payload(const void* buf, uint8_t len);

    /**
     * Read the receive payload
     *
     * The size of data read is the fixed payload size, see getPayloadSize()
     *
     * @param buf Where to put the data
     * @param len Maximum number of bytes to read
     * @return Current value of status register
     */
    uint8_t read_payload(void* buf, uint8_t len) ;

    /**
     * Read the payload length
     *
     * For dynamic payloads, this pulls the size of the payload off
     * the chip
     *
     * @return Payload length of last-received dynamic payload
     */
    uint8_t read_payload_length(void);

    /**
     * Empty the receive buffer
     *
     * @return Current value of status register
     */
    uint8_t flush_rx(void);

    /**
     * Empty the transmit buffer
     *
     * @return Current value of status register
     */
    uint8_t flush_tx(void);

    /**
     * Retrieve the current status of the chip
     *
     * @return Current value of status register
     */
    uint8_t get_status(void) ;

    /**
     * Decode and print the given status to stdout
     *
     * @param status Status value to print
     *
     * @warning Does nothing if stdout is not defined.  See fdevopen in stdio.h
     */
    void print_status(uint8_t status) ;

    /**
     * Decode and print the given 'observe_tx' value to stdout
     *
     * @param value The observe_tx value to print
     *
     * @warning Does nothing if stdout is not defined.  See fdevopen in stdio.h
     */
    void print_observe_tx(uint8_t value) ;

    /**
     * Print the name and value of an 8-bit register to stdout
     *
     * Optionally it can print some quantity of successive
     * registers on the same line.  This is useful for printing a group
     * of related registers on one line.
     *
     * @param name Name of the register
     * @param reg Which register. Use constants from nRF24L01.h
     * @param qty How many successive registers to print
     */
    void print_byte_register(prog_char* name, uint8_t reg, uint8_t qty = 1);
    
    /**
     * Print the name and value of a 40-bit address register to stdout
     *
     * Optionally it can print some quantity of successive
     * registers on the same line.  This is useful for printing a group
     * of related registers on one line.
     *
     * @param name Name of the register
     * @param reg Which register. Use constants from nRF24L01.h
     * @param qty How many successive registers to print
     */
    void print_address_register(prog_char* name, uint8_t reg, uint8_t qty = 1);
    
    /**
     * Turn on or off the special features of the chip
     *
     * The chip has certain 'features' which are only available when the 'features'
     * are enabled.  See the datasheet for details.
     */
    void toggle_features(void);
    /**@}*/

public:
    /**
     * @name Primary public interface
     *
     *  These are the main methods you need to operate the chip
     */
    /**@{*/

    /**
     * Constructor
     *
     * Creates a new instance of this driver.  Before using, you create an instance
     * and send in the unique pins that this chip is connected to.
     *
     * @param _cepin The pin attached to Chip Enable on the RF module
     * @param _cspin The pin attached to Chip Select
     */
    RF24(uint8_t _cepin, uint8_t _cspin);

    /**
     * Begin operation of the chip
     *
     * Call this in setup(), before calling any other methods.
     */
    void begin(void);

    /**
     * Start listening on the pipes opened for reading.
     *
     * Be sure to call openReadingPipe() first.  Do not call write() while
     * in this mode, without first calling stopListening().  Call
     * isAvailable() to check for incoming traffic, and read() to get it.
     */
    void startListening(void);

    /**
     * Stop listening for incoming messages
     *
     * Do this before calling write().
     */
    void stopListening(void);

    /**
     * Write to the open writing pipe
     *
     * Be sure to call openWritingPipe() first to set the destination
     * of where to write to.
     *
     * This blocks until the message is successfully acknowledged by
     * the receiver or the timeout/retransmit maxima are reached.  In
     * the current configuration, the max delay here is 60ms.
     *
     * The maximum size of data written is the fixed payload size, see
     * getPayloadSize().  However, you can write less, and the remainder
     * will just be filled with zeroes.
     *
     * @todo Write a non-blocking write to support users who want to 
     * check on progress separately or use an interrupt.
     *
     * @param buf Pointer to the data to be sent
     * @param len Number of bytes to be sent
     * @return True if the payload was delivered successfully false if not
     */
    boolean write( const void* buf, uint8_t len );

    /**
     * Test whether there are bytes available to be read
     *
     * @return True if there is a payload available, false if none is
     */
    boolean available(void) ;

    /**
     * Read the payload
     *
     * Return the last payload received
     *
     * The size of data read is the fixed payload size, see getPayloadSize()
     *
     * @note I specifically chose 'void*' as a data type to make it easier
     * for beginners to use.  No casting needed.
     *
     * @param buf Pointer to a buffer where the data should be written
     * @param len Maximum number of bytes to read into the buffer
     * @return True if the payload was delivered successfully false if not
     */
    boolean read( void* buf, uint8_t len ) ;

    /**
     * Open a pipe for writing
     *
     * Only one pipe can be open at once, but you can change the pipe
     * you'll listen to.  Do not call this while actively listening.
     * Remember to stopListening() first.
     *
     * Addresses are 40-bit hex values, e.g.:
     *
     * @code
     *   openWritingPipe(0xF0F0F0F0F0);
     * @endcode
     *
     * @param address The 40-bit address of the pipe to open.  This can be
     * any value whatsoever, as long as you are the only one writing to it
     * and only one other radio is listening to it.  Coordinate these pipe
     * addresses amongst nodes on the network.
     */
    void openWritingPipe(uint64_t address);

    /**
     * Open a pipe for reading
     *
     * Up to 6 pipes can be open for reading at once.  Open all the
     * reading pipes, and then call startListening().
     *
     * @see openWritingPipe
     *
     * @warning Pipes 1-5 should share the first 32 bits.
     * Only the least significant byte should be unique, e.g.
     * @code
     *   openReadingPipe(1,0xF0F0F0F0AA);
     *   openReadingPipe(2,0xF0F0F0F066);
     * @endcode
     *
     * @warning Pipe 0 is also used by the writing pipe.  So if you open
     * pipe 0 for reading, and then startListening(), it will overwrite the
     * writing pipe.  Ergo, do an openWritingPipe() again before write().
     *
     * @todo Enforce the restriction that pipes 1-5 must share the top 32 bits
     *
     * @param number Which pipe# to open, 0-5.
     * @param address The 40-bit address of the pipe to open.
     */
    void openReadingPipe(uint8_t number, uint64_t address);

    /**@}*/
    /**
     * @name Optional public interface
     *
     *  Methods you may want to use but are not needed for regular operation
     */
    /**@{*/

    /**
     * Set the number and delay of retries upon failed submit
     *
     * @param delay How long to wait between each retry, in multiples of 250us,
     * max is 15.  0 means 250us, 15 means 4000us.
     * @param count How many retries before giving up, max 15
     */
    void setRetries(uint8_t delay, uint8_t count);

    /**
     * Set RF communication channel
     *
     * @param channel Which RF channel to communicate on, 0-127
     */
    void setChannel(uint8_t channel);

    /**
     * Set Payload Size
     *
     * This implementation uses a pre-stablished fixed payload size for all
     * transmissions.  If this method is never called, the driver will always
     * transmit the maximum payload size (32 bytes), no matter how much
     * was sent to write().
     *
     * @todo Implement variable-sized payloads feature
     *
     * @param size The number of bytes in the payload
     */
    void setPayloadSize(uint8_t size);

    /**
     * Get Payload Size
     *
     * @see setPayloadSize()
     *
     * @return The number of bytes in the payload
     */
    uint8_t getPayloadSize(void) ;

    /**
     * Print a giant block of debugging information to stdout
     *
     * @warning Does nothing if stdout is not defined.  See fdevopen in stdio.h
     */
    void printDetails(void) ;

    /**
     * Enter low-power mode
     *
     * To return to normal power mode, either write() some data or
     * startListening().
     */
    void powerDown(void);

    /**
     * Test whether there are bytes available to be read
     *
     * Use this version to discover on which pipe the message
     * arrived.
     *
     * @param[out] pipe_num Which pipe has the payload available
     * @return True if there is a payload available, false if none is
     */
    boolean available(uint8_t* pipe_num);

    /**
     * Enable custom payloads on the acknowledge packets
     *
     * Ack payloads are a handy way to return data back to senders without
     * manually changing the radio modes on both units.
     *
     * @see examples/pingpair_pl/pingpair_pl.pde
     */
    void enableAckPayload(void);

    /**
     * Write an ack payload for the specified pipe
     *
     * The next time a message is received on @p pipe, the data in @p buf will
     * be sent back in the acknowledgement.
     *
     * @warning According to the data sheet, only three of these can be pending
     * at any time.  I have not tested this.
     *
     * @param pipe Which pipe# (typically 1-5) will get this response.
     * @param buf Pointer to data that is sent
     * @param len Length of the data to send, up to 32 bytes max.  Not affected
     * by the static payload set by setPayloadSize().
     */
    void writeAckPayload(uint8_t pipe, const void* buf, uint8_t len);

    /**
     * Determine if an ack payload was received in the most recent call to
     * write().
     *
     * Call read() to retrieve the ack payload.
     *
     * @warning Calling this function clears the internal flag which indicates
     * a payload is available.  If it returns true, you must read the packet
     * out as the very next interaction with the radio, or the results are
     * undefined.
     *
     * @return True if an ack payload is available.
     */
    boolean isAckPayloadAvailable(void);

    /**
     * Enable or disable auto-acknowlede packets
     *
     * This is enabled by default, so it's only needed if you want to turn
     * it off for some reason.
     *
     * @param enable Whether to enable (true) or disable (false) auto-acks
     */
    void setAutoAck(bool enable);

    /**
     * Test whether there was a carrier on the line for the
     * previous listening period.
     *
     * Useful to check for interference on the current channel.
     *
     * @return true if was carrier, false if not
     */
    boolean testCarrier(void);

    /**
     * Set the transmission data rate
     *
     * @param speed RF24_1MBPS for 1Mbps or RF24_2MBPS for 2Mbps
     */
    void setDataRate(rf24_datarate_e speed);

    /**
     * Set the CRC length
     *
     * @param length RF24_CRC_8 for 8-bit or RF24_CRC_16 for 16-bit
     */
    void setCRCLength(rf24_crclength_e length);

    /**@}*/
};

/**
 * @example led_remote.pde
 *
 * This is an example of how to use the RF24 class to control a remote
 * bank of LED's using buttons on a remote control.
 *
 * Every time the buttons change on the remote, the entire state of
 * buttons is send to the led board, which displays the state.
 */

/**
 * @example pingpair.pde
 *
 * This is an example of how to use the RF24 class.  Write this sketch to two
 * different nodes, connect the role_pin to ground on one.  The ping node sends
 * the current time to the pong node, which responds by sending the value back.
 * The ping node can then see how long the whole cycle took.
 */

/**
 * @example starping.pde
 *
 * This sketch is a more complex example of using the RF24 library for Arduino.
 * Deploy this on up to six nodes.  Set one as the 'pong receiver' by tying the
 * role_pin low, and the others will be 'ping transmit' units.  The ping units
 * unit will send out the value of millis() once a second.  The pong unit will
 * respond back with a copy of the value.  Each ping unit can get that response
 * back, and determine how long the whole cycle took.
 *
 * This example requires a bit more complexity to determine which unit is which.
 * The pong receiver is identified by having its role_pin tied to ground.
 * The ping senders are further differentiated by a byte in eeprom.
 */

/**
 * @example pingpair_pl.pde
 *
 * This is an example of how to do two-way communication without changing
 * transmit/receive modes.  Here, a payload is set to the transmitter within
 * the Ack packet of each transmission.  Note that the payload is set BEFORE
 * the sender's message arrives.
 */

/**
 * @example pingpair_sleepy.pde
 *
 * This is an example of how to use the RF24 class to create a battery-
 * efficient system.  It is just like the pingpair.pde example, but the
 * ping node powers down the radio and sleeps the MCU after every
 * ping/pong cycle.
 */

/**
 * @example scanner.pde
 *
 * Example to detect interference on the various channels available.
 * This is a good diagnostic tool to check whether you're picking a
 * good channel for your application.
 *
 * Inspired by cpixip.
 * See http://arduino.cc/forum/index.php/topic,54795.0.html
 */

/**
 * @mainpage Driver for nRF24L01(+) 2.4GHz Wireless Transceiver
 *
 * Design Goals: This library is designed to be...
 * @li Maximally compliant with the intended operation of the chip
 * @li Easy for beginners to use
 * @li Consumed with a public interface that's similiar to other Arduino standard libraries
 * @li Built against the standard SPI library.
 *
 * Please refer to:
 *
 * @li <a href="http://maniacbug.github.com/RF24/">Documentation Main Page</a>
 * @li <a href="http://maniacbug.github.com/RF24/classRF24.html">RF24 Class Documentation</a>
 * @li <a href="https://github.com/maniacbug/RF24/">Source Code</a>
 * @li <a href="https://github.com/maniacbug/RF24/archives/master">Downloads Page</a>
 * @li <a href="http://www.nordicsemi.com/files/Product/data_sheet/nRF24L01_Product_Specification_v2_0.pdf">Chip Datasheet</a>
 *
 * This chip uses the SPI bus, plus two chip control pins.  Remember that pin 10 must still remain an output, or
 * the SPI hardware will go into 'slave' mode.
 */

#endif // __RF24_H__
// vim:ai:cin:sts=2 sw=2 ft=cpp