hydroponic-controller/include/ec.h

#ifndef _EC_H_
#define _EC_H_

#include <Arduino.h>


bool ec_flag_measurement_available=false;

#define EC_PIN_RELAY_PROBE 27


//#define EC_PIN_ADC 4
#define EC_ADS_CHANNEL 0
#define EC_PIN_FREQ 5
#define EC_PWM_CH 0
#define EC_RESOLUTION 8
#define EC_FREQUENCY 5000

#define EC_CALIB_ARRAY_SIZE 256
uint16_t ec_calib_array[EC_CALIB_ARRAY_SIZE];
uint16_t ec_calib_array_pos=0;
#define EC_CALIB_READ_INTERVAL 250 //interval of reading adc value inside a measurement

#define EC_ARRAY_SIZE 256
uint16_t ec_array[EC_ARRAY_SIZE];
uint16_t ec_array_pos=EC_ARRAY_SIZE;
unsigned long last_measurement_ec=0;
#define EC_MEASUREMENT_INTERVAL 30000 //complete filtered measurement every x ms
  //One filtered measurement takes EC_READ_INTERVAL*EC_ARRAY_SIZE*4
#define EC_READ_INTERVAL 10 //interval of reading adc value inside a measurement. one reading takes about 9-10ms

#define EC_RELAY_SWITCH_SETTLETIME 500  //time until voltage of ec circuit has settled

//const uint16_t ec_centerADCvalue=9026; //adc value when probe resistance is equal to the range resistor (mean of both)
//Range Resistor is two parallel 1k2 = 600 Ohm

unsigned long ec_last_change_relay=0; //millis of last relay change

enum ECState{IDLE,MEASURE};

ECState ecstate=IDLE;

float ec_adc;
float ec_adc_adjusted; //adjusted for reference resistor
float ec_calib_adc;
float ec; //ec value after adjustment for reference (at current temperature)
float ec25; //ec value but temperature adjusted for 25 degC

float ec_tempadjust_alpa=0.2; //TODO
float ec_reference_adc=6016.88; //adc reference value for the calibration resistor measurement.

//x^0*p[0] + ... + x^n*p[n]
//float ec_calibration_polynom[]={691.5992624638029,-1.4015367296761692,0.0008513503472324141,-2.2140576823179093e-07,2.8962580780180067e-11,-1.8577565383307114e-15,4.7162479484903865e-20};
float ec_calibration_polynom[]={1033.928052655456,-3.8909104921922895,0.005627541436014758,-4.103988840997024e-06,1.7231981870816133e-09,-4.433707707721975e-13,7.203892111369395e-17,-7.406549810844244e-21,4.667420606439905e-25,-1.6439457516812463e-29,2.477292190335455e-34};
float ec_calibration_linearize_below_adc=0; //use linear approximation below this adc value. 0=disable
float ec_calibration_linear_lowADC=830; //x0
float ec_calibration_linear_lowEC=0; //y0

bool ec_measurementReady();
void ec_startMeasurement();
void ec_setRange(uint8_t range);
void ec_connectProbe(bool);
void ec_releaseRelay();
float ec_getECfromADC(float adc);

void ec_setup() {
  ledcSetup(EC_PWM_CH, EC_FREQUENCY, EC_RESOLUTION);
  ledcAttachPin(EC_PIN_FREQ, EC_PWM_CH);
  ledcWrite(EC_PWM_CH, 127); //50% duty cycle

  pinMode(EC_PIN_RELAY_PROBE,OUTPUT); //LOW=Calibration/idle, HIGH=Probe connected
  ec_releaseRelay();

}

void ec_loop(unsigned long loopmillis) {
  
  static unsigned long last_read_ec=0;

  switch (ecstate) {
    case IDLE:
      
      if (loopmillis>last_measurement_ec+EC_MEASUREMENT_INTERVAL && ecstate==IDLE) { //start measurement if idle
        last_measurement_ec=loopmillis;
        ec_startMeasurement();
        ec_connectProbe(true);
        
        ecstate=MEASURE;
      }
      break;

    case MEASURE:
      if (ec_measurementReady()) {
        ec_releaseRelay();
        ec_adc=getMean(ec_array,EC_ARRAY_SIZE);
        if (isValueArrayOK(ec_calib_array,EC_CALIB_ARRAY_SIZE,0)){
          ec_calib_adc=getMean(ec_calib_array,EC_CALIB_ARRAY_SIZE);
          ec_adc_adjusted=mapf(ec_adc,0,ec_calib_adc,0,ec_reference_adc);
          ec=ec_getECfromADC(ec_adc_adjusted);
        }

        ec_flag_measurement_available=true;

        ecstate=IDLE;
      }
      
      break;

  }


  if (ec_array_pos<EC_ARRAY_SIZE) { //measurement running
    if (loopmillis>last_read_ec+EC_READ_INTERVAL) { //take reading into array
      last_read_ec=loopmillis;

      if (loopmillis>ec_last_change_relay+EC_RELAY_SWITCH_SETTLETIME) { //values have settled        
        uint16_t value = ADS.readADC(EC_ADS_CHANNEL);
        
        ec_array[ec_array_pos]=value;
        
        ec_array_pos++;
      }
    }
  }else{ //measurement not running, then take calibration readings
    if (loopmillis>last_read_ec+EC_CALIB_READ_INTERVAL) { //take reading into array
      last_read_ec=loopmillis;

      if (loopmillis>ec_last_change_relay+EC_RELAY_SWITCH_SETTLETIME) { //values have settled        
        uint16_t value = ADS.readADC(EC_ADS_CHANNEL);
        
        ec_calib_array[ec_calib_array_pos]=value;
        
        ec_calib_array_pos++;
        ec_calib_array_pos%=EC_CALIB_ARRAY_SIZE;

        
      }
    }
  }
  
}



void ec_startMeasurement() {
  ec_array_pos=0;
}

bool ec_measurementReady(){
  if (ec_array_pos>=EC_ARRAY_SIZE) { //reached end of both arrays
    return true;
  }else{
    return false;
  }
}


void ec_connectProbe(bool relay) {
  bool val=digitalRead(EC_PIN_RELAY_PROBE);
  if (val!=relay) { //write only if different
    digitalWrite(EC_PIN_RELAY_PROBE,relay);
    ec_last_change_relay=millis();
  }
}

void ec_releaseRelay() {
  digitalWrite(EC_PIN_RELAY_PROBE,LOW);
  ec_last_change_relay=millis();
}

float ec_getECfromADC(float adc) {
  uint8_t polynom_order=sizeof(ec_calibration_polynom) / sizeof(ec_calibration_polynom[0]);
  double _ec=0;
  if (adc>=ec_calibration_linearize_below_adc) { //adc is in range where polynomial approximation fits well
    for (uint8_t i=0;i<polynom_order;i++) {
      _ec+=pow(adc,i)*ec_calibration_polynom[i];
    }
  }else{ //low ec region. linear approximation works better here
    float x1=ec_calibration_linearize_below_adc;
    float y1=0;
    for (uint8_t i=0;i<polynom_order;i++) { //get y1 value from curve
      y1+=pow(x1,i)*ec_calibration_polynom[i];
    }
    float x0=ec_calibration_linear_lowADC;
    float y0=ec_calibration_linear_lowEC;

    _ec=mapf(adc,x0,x1,y0,y1); //linear approximation    
  }
  return _ec;
}


#endif