260 lines
7.3 KiB
C
260 lines
7.3 KiB
C
|
|
#include <stdbool.h>
|
|
#include <string.h>
|
|
#include "stm32f1xx_hal.h"
|
|
#include "defines.h"
|
|
#include "setup.h"
|
|
#include "config.h"
|
|
|
|
TIM_HandleTypeDef TimHandle;
|
|
TIM_HandleTypeDef TimHandle2;
|
|
uint8_t ppm_count = 0;
|
|
uint8_t pwm_count = 0;
|
|
uint32_t timeoutCntGen = TIMEOUT;
|
|
uint8_t timeoutFlgGen = 0;
|
|
uint8_t nunchuk_data[6] = {0};
|
|
|
|
uint8_t i2cBuffer[2];
|
|
|
|
extern I2C_HandleTypeDef hi2c2;
|
|
extern DMA_HandleTypeDef hdma_i2c2_rx;
|
|
extern DMA_HandleTypeDef hdma_i2c2_tx;
|
|
|
|
#if defined(CONTROL_PPM_LEFT) || defined(CONTROL_PPM_RIGHT)
|
|
uint16_t ppm_captured_value[PPM_NUM_CHANNELS + 1] = {500, 500};
|
|
uint16_t ppm_captured_value_buffer[PPM_NUM_CHANNELS+1] = {500, 500};
|
|
uint32_t ppm_timeout = 0;
|
|
|
|
bool ppm_valid = true;
|
|
|
|
void PPM_ISR_Callback(void) {
|
|
// Dummy loop with 16 bit count wrap around
|
|
uint16_t rc_delay = TIM2->CNT;
|
|
TIM2->CNT = 0;
|
|
|
|
if (rc_delay > 3000) {
|
|
if (ppm_valid && ppm_count == PPM_NUM_CHANNELS) {
|
|
ppm_timeout = 0;
|
|
timeoutCntGen = 0;
|
|
timeoutFlgGen = 0;
|
|
memcpy(ppm_captured_value, ppm_captured_value_buffer, sizeof(ppm_captured_value));
|
|
}
|
|
ppm_valid = true;
|
|
ppm_count = 0;
|
|
}
|
|
else if (ppm_count < PPM_NUM_CHANNELS && IN_RANGE(rc_delay, 900, 2100)){
|
|
ppm_captured_value_buffer[ppm_count++] = CLAMP(rc_delay, 1000, 2000) - 1000;
|
|
} else {
|
|
ppm_valid = false;
|
|
}
|
|
}
|
|
|
|
// SysTick executes once each ms
|
|
void PPM_SysTick_Callback(void) {
|
|
ppm_timeout++;
|
|
// Stop after 500 ms without PPM signal
|
|
if(ppm_timeout > 500) {
|
|
int i;
|
|
for(i = 0; i < PPM_NUM_CHANNELS; i++) {
|
|
ppm_captured_value[i] = 500;
|
|
}
|
|
ppm_timeout = 0;
|
|
}
|
|
}
|
|
|
|
void PPM_Init(void) {
|
|
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|
/*Configure GPIO pin : PA3 */
|
|
GPIO_InitStruct.Pin = PPM_PIN;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
|
|
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
|
|
HAL_GPIO_Init(PPM_PORT, &GPIO_InitStruct);
|
|
|
|
__HAL_RCC_TIM2_CLK_ENABLE();
|
|
TimHandle.Instance = TIM2;
|
|
TimHandle.Init.Period = UINT16_MAX;
|
|
TimHandle.Init.Prescaler = (SystemCoreClock/DELAY_TIM_FREQUENCY_US)-1;;
|
|
TimHandle.Init.ClockDivision = 0;
|
|
TimHandle.Init.CounterMode = TIM_COUNTERMODE_UP;
|
|
HAL_TIM_Base_Init(&TimHandle);
|
|
|
|
#if defined(CONTROL_PPM_LEFT)
|
|
/* EXTI interrupt init*/
|
|
HAL_NVIC_SetPriority(EXTI3_IRQn, 0, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI3_IRQn);
|
|
#endif
|
|
|
|
#if defined(CONTROL_PPM_RIGHT)
|
|
/* EXTI interrupt init*/
|
|
HAL_NVIC_SetPriority(EXTI15_10_IRQn, 0, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI15_10_IRQn);
|
|
#endif
|
|
|
|
HAL_TIM_Base_Start(&TimHandle);
|
|
}
|
|
#endif
|
|
|
|
|
|
#if defined(CONTROL_PWM_LEFT) || defined(CONTROL_PWM_RIGHT)
|
|
/*
|
|
* Illustration of the PWM functionality
|
|
* CH1 ________|‾‾‾‾‾‾‾‾‾‾|________
|
|
* CH2 ______________|‾‾‾‾‾‾‾‾‾‾‾|________
|
|
* ↑ ↑ ↑ ↑
|
|
* TIM2 RST SAVE RC_CH1 RC_CH1
|
|
*/
|
|
|
|
uint16_t pwm_captured_ch1_value = 500;
|
|
uint16_t pwm_captured_ch2_value = 500;
|
|
uint16_t pwm_CNT_prev_ch1 = 0;
|
|
uint16_t pwm_CNT_prev_ch2 = 0;
|
|
uint32_t pwm_timeout_ch1 = 0;
|
|
uint32_t pwm_timeout_ch2 = 0;
|
|
|
|
void PWM_ISR_CH1_Callback(void) {
|
|
// Dummy loop with 16 bit count wrap around
|
|
if(HAL_GPIO_ReadPin(PWM_PORT_CH1, PWM_PIN_CH1)) { // Rising Edge interrupt -> save timer value OR reset timer
|
|
if (HAL_GPIO_ReadPin(PWM_PORT_CH2, PWM_PIN_CH2)) {
|
|
pwm_CNT_prev_ch1 = TIM2->CNT;
|
|
} else {
|
|
TIM2->CNT = 0;
|
|
pwm_CNT_prev_ch1 = 0;
|
|
}
|
|
} else { // Falling Edge interrupt -> measure pulse duration
|
|
uint16_t rc_signal = TIM2->CNT - pwm_CNT_prev_ch1;
|
|
if (IN_RANGE(rc_signal, 900, 2100)){
|
|
timeoutCntGen = 0;
|
|
timeoutFlgGen = 0;
|
|
pwm_timeout_ch1 = 0;
|
|
pwm_captured_ch1_value = CLAMP(rc_signal, 1000, 2000) - 1000;
|
|
}
|
|
}
|
|
}
|
|
|
|
void PWM_ISR_CH2_Callback(void) {
|
|
// Dummy loop with 16 bit count wrap around
|
|
if(HAL_GPIO_ReadPin(PWM_PORT_CH2, PWM_PIN_CH2)) { // Rising Edge interrupt -> save timer value OR reset timer
|
|
if (HAL_GPIO_ReadPin(PWM_PORT_CH1, PWM_PIN_CH1)) {
|
|
pwm_CNT_prev_ch2 = TIM2->CNT;
|
|
} else {
|
|
TIM2->CNT = 0;
|
|
pwm_CNT_prev_ch2 = 0;
|
|
}
|
|
} else { // Falling Edge interrupt -> measure pulse duration
|
|
uint16_t rc_signal = TIM2->CNT - pwm_CNT_prev_ch2;
|
|
if (IN_RANGE(rc_signal, 900, 2100)){
|
|
timeoutCntGen = 0;
|
|
timeoutFlgGen = 0;
|
|
pwm_timeout_ch2 = 0;
|
|
pwm_captured_ch2_value = CLAMP(rc_signal, 1000, 2000) - 1000;
|
|
}
|
|
}
|
|
}
|
|
|
|
// SysTick executes once each ms
|
|
void PWM_SysTick_Callback(void) {
|
|
pwm_timeout_ch1++;
|
|
pwm_timeout_ch2++;
|
|
// Stop after 500 ms without PWM signal
|
|
if(pwm_timeout_ch1 > 500) {
|
|
pwm_captured_ch1_value = 500;
|
|
pwm_timeout_ch1 = 0;
|
|
}
|
|
if(pwm_timeout_ch2 > 500) {
|
|
pwm_captured_ch2_value = 500;
|
|
pwm_timeout_ch2 = 0;
|
|
}
|
|
}
|
|
|
|
void PWM_Init(void) {
|
|
// PWM Timer (TIM2)
|
|
__HAL_RCC_TIM2_CLK_ENABLE();
|
|
TimHandle.Instance = TIM2;
|
|
TimHandle.Init.Period = UINT16_MAX;
|
|
TimHandle.Init.Prescaler = (SystemCoreClock/DELAY_TIM_FREQUENCY_US)-1;;
|
|
TimHandle.Init.ClockDivision = 0;
|
|
TimHandle.Init.CounterMode = TIM_COUNTERMODE_UP;
|
|
HAL_TIM_Base_Init(&TimHandle);
|
|
|
|
// Channel 1 (steering)
|
|
GPIO_InitTypeDef GPIO_InitStruct1 = {0};
|
|
// Configure GPIO pin : PA2 (Left) or PB10 (Right)
|
|
GPIO_InitStruct1.Pin = PWM_PIN_CH1;
|
|
GPIO_InitStruct1.Mode = GPIO_MODE_IT_RISING_FALLING;
|
|
GPIO_InitStruct1.Speed = GPIO_SPEED_FREQ_HIGH;
|
|
GPIO_InitStruct1.Pull = GPIO_PULLDOWN;
|
|
HAL_GPIO_Init(PWM_PORT_CH1, &GPIO_InitStruct1);
|
|
|
|
// Channel 2 (speed)
|
|
GPIO_InitTypeDef GPIO_InitStruct2 = {0};
|
|
/*Configure GPIO pin : PA3 (Left) or PB11 (Right) */
|
|
GPIO_InitStruct2.Pin = PWM_PIN_CH2;
|
|
GPIO_InitStruct2.Mode = GPIO_MODE_IT_RISING_FALLING;
|
|
GPIO_InitStruct2.Speed = GPIO_SPEED_FREQ_HIGH;
|
|
GPIO_InitStruct2.Pull = GPIO_PULLDOWN;
|
|
HAL_GPIO_Init(PWM_PORT_CH2, &GPIO_InitStruct2);
|
|
|
|
#ifdef CONTROL_PWM_LEFT
|
|
/* EXTI interrupt init*/
|
|
HAL_NVIC_SetPriority(EXTI2_IRQn, 0, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI2_IRQn);
|
|
HAL_NVIC_SetPriority(EXTI3_IRQn, 0, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI3_IRQn);
|
|
#endif
|
|
|
|
#ifdef CONTROL_PWM_RIGHT
|
|
/* EXTI interrupt init*/
|
|
HAL_NVIC_SetPriority(EXTI15_10_IRQn, 0, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI15_10_IRQn);
|
|
#endif
|
|
|
|
// Start timer
|
|
HAL_TIM_Base_Start(&TimHandle);
|
|
}
|
|
#endif
|
|
|
|
uint8_t Nunchuk_Ping(void) {
|
|
if (HAL_I2C_Master_Receive(&hi2c2,0xA4,(uint8_t*)nunchuk_data, 1, 10) == HAL_OK) {
|
|
return 1;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
void Nunchuk_Init(void) {
|
|
//-- START -- init WiiNunchuk
|
|
i2cBuffer[0] = 0xF0;
|
|
i2cBuffer[1] = 0x55;
|
|
|
|
HAL_I2C_Master_Transmit(&hi2c2,0xA4,(uint8_t*)i2cBuffer, 2, 100);
|
|
HAL_Delay(10);
|
|
|
|
i2cBuffer[0] = 0xFB;
|
|
i2cBuffer[1] = 0x00;
|
|
|
|
HAL_I2C_Master_Transmit(&hi2c2,0xA4,(uint8_t*)i2cBuffer, 2, 100);
|
|
HAL_Delay(10);
|
|
}
|
|
|
|
void Nunchuk_Read(void) {
|
|
i2cBuffer[0] = 0x00;
|
|
HAL_I2C_Master_Transmit(&hi2c2,0xA4,(uint8_t*)i2cBuffer, 1, 10);
|
|
HAL_Delay(3);
|
|
if (HAL_I2C_Master_Receive(&hi2c2,0xA4,(uint8_t*)nunchuk_data, 6, 10) == HAL_OK) {
|
|
timeoutCntGen = 0;
|
|
timeoutFlgGen = 0;
|
|
}
|
|
|
|
#ifndef TRANSPOTTER
|
|
if (timeoutCntGen > 3) {
|
|
HAL_Delay(50);
|
|
Nunchuk_Init();
|
|
}
|
|
#endif
|
|
|
|
//setScopeChannel(0, (int)nunchuk_data[0]);
|
|
//setScopeChannel(1, (int)nunchuk_data[1]);
|
|
//setScopeChannel(2, (int)nunchuk_data[5] & 1);
|
|
//setScopeChannel(3, ((int)nunchuk_data[5] >> 1) & 1);
|
|
}
|