abgefragt am Thu Jan 9 23:03:05 CET 2020 smartctl 7.0 2018-12-30 r4883 [x86_64-linux-5.3.0-26-generic] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE4-GP Device Model: WDC WD2002FYPS-01U1B1 Serial Number: WD-WCAVY4825044 LU WWN Device Id: 5 0014ee 204c1f986 Firmware Version: 04.05G05 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Jan 9 23:03:05 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40260) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 459) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 121 3 Spin_Up_Time 0x0027 150 149 021 Pre-fail Always - 9500 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 59 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 008 008 000 Old_age Always - 67488 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 59 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 50 193 Load_Cycle_Count 0x0032 088 088 000 Old_age Always - 336607 194 Temperature_Celsius 0x0022 126 082 000 Old_age Always - 26 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 45 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 295 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 295 occurred at disk power-on lifetime: 1943 hours (80 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 83 3d 10 40 Error: UNC at LBA = 0x00103d83 = 1064323 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 80 80 3d 10 40 00 01:08:30.112 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:08:11.060 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:08:07.593 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:07:48.542 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:07:43.696 READ VERIFY SECTOR(S) Error 294 occurred at disk power-on lifetime: 1943 hours (80 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 83 3d 10 40 Error: UNC at LBA = 0x00103d83 = 1064323 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 80 80 3d 10 40 00 01:08:07.593 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:07:48.542 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:07:43.696 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:07:24.645 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:07:19.549 READ VERIFY SECTOR(S) Error 293 occurred at disk power-on lifetime: 1943 hours (80 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 85 3d 10 40 Error: UNC at LBA = 0x00103d85 = 1064325 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 80 80 3d 10 40 00 01:07:43.696 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:07:24.645 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:07:19.549 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:07:00.498 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:06:56.891 READ VERIFY SECTOR(S) Error 292 occurred at disk power-on lifetime: 1943 hours (80 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 85 3d 10 40 Error: UNC at LBA = 0x00103d85 = 1064325 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 80 80 3d 10 40 00 01:07:19.549 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:07:00.498 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:06:56.891 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:06:37.839 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:06:33.743 READ VERIFY SECTOR(S) Error 291 occurred at disk power-on lifetime: 1943 hours (80 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 80 83 3d 10 40 Error: UNC at LBA = 0x00103d83 = 1064323 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 80 80 3d 10 40 00 01:06:56.891 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:06:37.839 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:06:33.743 READ VERIFY SECTOR(S) ef 03 46 00 00 00 00 00 01:06:14.692 SET FEATURES [Set transfer mode] 40 00 80 80 3d 10 40 00 01:06:10.665 READ VERIFY SECTOR(S) SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.